Search Results

There are now several wind tunnel facilities within Europe for testing passenger cars with and without moving ground and rotating wheel conditions (henceforth abbreviated to MVG&RW conditions). Within these facilities, the drag of a car under MVG&RW conditions is typically less than the drag of a car under stationary ground and stationary wheel conditions. This drag difference has been found to vary from a decrease of about 25 drag counts to a small drag increase according to published sources. A drag reduction of 10 to 20 drag counts is more typical, however.

The transition towards battery electric vehicles (BEVs) has increased the focus of vehicle manufacturers on energy efficiency. Ensuring adequate airflow through the heat exchanger is necessary to climatize the vehicle, at the cost of an increase in the aerodynamic drag. With lower cooling airflow requirements in BEVs during driving, the front air intakes could be made smaller and thus be placed with greater freedom. This paper explores the effects on exterior aerodynamics caused by securing a constant cooling airflow through intakes at various positions across the front of the vehicle. High-fidelity simulations were performed on a variation of the open-source AeroSUV model that is more representative of a BEV configuration. To focus on the exterior aerodynamic changes, and under the assumption that the cooling requirements would remain the same for a given driving condition, a constant mass flow boundary condition was defined at the cooling airflow inlets and outlets.

The automotive industry strives to develop high quality vehicles in a short period of time that satisfy the consumer needs and stand out in the competition. Full exploitation of simulation and Computer-Aided Engineering (CAE) tools can enable quick evaluation of different vehicle concepts and setups without the need of building physical prototypes. Addressing the aforementioned statements this paper presents a method for optimising the Electric Power-Assisted Steering (EPAS) ECU parameters employing solely CAE. The objective of the optimisation is to achieve a desired steering response. The developed process is tested on three specific steering metrics (friction feel, torque build-up and torque deadband) for two function parameters (basic steering torque and active return) of the EPAS. The optimisation method enabled all metrics to fall successfully within the target range.

The objective of this investigation was to improve the thermal properties of plasma sprayed thermal barrier coatings (TBC) for internal combustion engines. There is a need for further reduction of thermal conductivity and volumetric heat capacity and the negative effects on heat loss and combustion phasing of surface roughness and permeable porosity, typical for plasma sprayed coatings, should be minimized. Four measures for improvement of TBC properties were evaluated: i) modification of the coating's microstructure by using a novel suspension plasma spraying method, ii) application of gadolinium-zirconate, a novel ceramic material with low thermal conductivity, iii) polishing of the coating to achieve low surface roughness, and iv) sealing of the porous coating surface with a polysilazane. Six coating variants with different combinations of the selected measures were applied on the piston crown and evaluated in a single cylinder light duty diesel engine.

With the increase in fuel prices and the increasingly strict environmental legislations regarding CO₂ emissions, reduction of the total energy consumption of our society becomes more important. Passenger vehicles are partly responsible for this consumption due to their strong presence in the daily life of most people. Therefore reducing the impact of cars on the environment can assist in decreasing the overall energy consumption. Even though several fields have an impact on a passenger car's performance, this paper will focus on the aerodynamic part and more specifically, the wake behind a vehicle. By definition a car is a bluff body on which the air resistance is for the most part driven by pressure drag. This is caused by the wake these bodies create. Therefore analyzing the wake characteristics behind a vehicle is crucial if one would like to reduce drag.

A finite-element (FE) based method for numerically predicting fatigue life of MAG-welded thin-sheet structures has been established and tested. The method uses nodal forces and moments calculated along the weld line, together with an analytical expression for the structural stress at the weld toe. The calculated stress is used together with an experimentally determined Wöhler, or S-N, curve. A “stiff” welded joint with structural stress dominated by membrane forces is found to have a steeper S-N curve than a “flexible” joint with structural stress dominated by bending moment. All test results were seen to lie close to one of two different S-N curves. The proportion of bending stress over total structural stress could be used for choosing the appropriate S-N curve.

The following paper describes how to measure the global torsional stiffness of a complete car under field-like conditions. All that's needed are lifting devices, two stands of equal height, three glide planes or equivalent, three scales and two inclinometers, a spirit level, some pieces of aluminum and a glue gun. The results from four measured cars are presented and a comparison is made with values obtained with laboratory equipment and data from manufacturers. The method is a fast and economic means to find the most interesting cars that then can be selected for measurement by traditional methods, giving the stiffness as a function of the vehicles long axis, and thus minimizes the cost of benchmarking. Time for measuring one car with all equipment readily available and with personnel having some experience of the method is about two hours. Only the sway bars have to be disconnected. Absolutely no damage to the measured car means that rented cars can be used.

In the EU regulations, specification's for diesel fuel quality is regulated in the standard EN590. Sweden has however for many years used an “Environmental Class 1” (EC1) diesel fuel. In addition to fulfilling the EN590 standard, the main difference today between the Swedish EC1 and the EN590 fuel specifications is that higher levels of aromatics and polyaromatics (PAH) are allowed in the EN590 standard. Aromatics are considered to be potentially mutagenic, and the higher levels of aromatics also lead to increased particle emissions. Earlier studies of the exhaust emissions from engines using the different fuel qualities have shown significant differences, both regarding regulated emissions and health effects. In these studies, vehicles from emission standard Euro III and older have been used. The scope of this study was to investigate whether the differences persist for a modern Euro V vehicle or not.

Galvanic corrosion between die cast AZ91D and AM60B and different fastener systems has been evaluated by exposure on trucks and in accelerated laboratory tests. The exposure time on the trucks was 3 years, corresponding to a mileage of about 300000 km. Samples were retracted and evaluated after 1 and 2 years exposure. Similar samples were also exposed to the Volvo Indoor Corrosion Test and the General Motors GM9540P-cycle B test. The correlation between the field data and the laboratory tests was evaluated, as was the sharp difference in the performance of the fastener systems in the two accelerated laboratory tests.

Efforts towards ever more energy efficient passenger cars have become one of the largest challenges of the automotive industry. This involves numerous different fields of engineering, and every finished model is always a compromise between different requirements. Passenger car aerodynamics is no exception; the shape of the exterior is often dictated by styling, engine bay region by packaging issues etcetera. Wheel design is also a compromise between different requirements such as aerodynamic drag and brake cooling, but as the wheels and wheel housings are responsible for up to a quarter of the overall aerodynamic drag on a modern passenger car, it is not surprising that efforts are put towards improving the wheel aerodynamics.

This paper describes the experimental study of a tumble-flap mounted in the intake port of a single-cylinder spark-ignited gasoline engine. The research question addressed was whether an optimal tumble level could be found for the combustion system under investigation. Indicated fuel consumption was measured for a number of part-load operating points with the tumble-flap either open or closed. The experimental results were subjected to an energy balance analysis to understand which portion of the fuel energy was converted to work and how much was lost by incomplete combustion, heat losses to walls and to the exhaust gases, as well as to pumping losses. Closing the tumble-flap resulted in reduced fuel consumption only in a small area of the operating map: only at low-speed, low-load operation, a benefit could be obtained.

Passenger car fuel consumption is a constant concern for automotive companies and the contribution to fuel consumption from aerodynamics is well known. Several studies have been published on the aerodynamics of wheels. One area of wheel aerodynamics discussed in some of these earlier works is the so-called ventilation resistance. This study investigates ventilation resistance on a number of 17 inch rims, in the Volvo Cars Aerodynamic Wind Tunnel. The ventilation resistance was measured using a custom-built suspension with a tractive force measurement system installed in the Wheel Drive Units (WDUs). The study aims at identifying wheel design factors that have significant effect on the ventilation resistance for the investigated wheel size. The results show that it was possible to measure similar power requirements to rotate the wheels as was found in previous works.

It is well known that wheels are responsible for a significant amount of the total aerodynamic drag of passenger vehicles. Tyres, and mostly rims, have been the subject of research in the automotive industry for the past years, but their effect and interaction with each other and with the car exterior is still not completely understood. This paper focuses on the use of CFD to study the effects of tyre geometry (tyre profile and tyre tread) on road vehicle aerodynamics. Whenever possible, results of the numerical computations are compared with experiments. More than sixty configurations were simulated. These simulations combined different tyre profiles, treads, rim designs and spoke orientation on two car types: a sedan and a sports wagon. Two tyre geometries were obtained directly from the tyre manufacturer, while a third geometry was obtained from our database and represents a generic tyre which covers different profiles of a given tyre size.

The aerodynamic drag, fuel consumption and hence CO2 emissions, of a road vehicle depend strongly on its flow structures and the pressure drag generated. The rear end flow which is an area of complex three-dimensional flow structures, contributes to the wake development and the overall aerodynamic performance of the vehicle. This paper seeks to provide improved insight into this flow region to better inform future drag reduction strategies. Using experimental and numerical techniques, two vehicle shapes have been studied; a 30% scale model of a Volvo S60 representing a 2003MY vehicle and a full scale 2010MY S60. First the surface topology of the rear end (rear window and trunk deck) of both configurations is analysed, using paint to visualise the skin friction pattern. By means of critical points, the pattern is characterized and changes are identified studying the location and type of the occurring singularities.

Experience from several car projects shows that S-N curves for spot welds generated under load control in the high cycle fatigue regime might be very conservative when used in the low cycle fatigue regime. Therefore, force and displacement controlled low cycle fatigue tests were carried out on peel and shear loaded specimens. Both constant (CA) and variable amplitude (VA) load signals were used. Finally, a method for predicting fatigue life of spot welds with increased accuracy in the low cycle fatigue regime is proposed. The method is simple, fast and accurate and can be used together with linear finite element analysis (FEA) and existing fatigue packages.

Alternative-fuelled vehicles are a growing market, and emission performance of these vehicles should be thoroughly investigated. The emission legislation is however very diversified in different countries; a short summary of the legislation in the EU, the USA and Brazil is presented in this study. In the EU regulations, everything measured with the FID (Flame Ionization Detector) is treated as hydrocarbon emissions. In the USA the alcohols and aldehydes are measured and reported separately from hydrocarbons. In Brazil, the alcohol part can be measured separately on voluntary basis. The influence of some of these differences has been further investigated in this report. Results from two related studies are presented. The FID response for ethanol was investigated and emission testing of an E85-fuelled FFV (Flex Fuel Vehicle) was performed.

Fuel consumption of vehicles has received increased attention in recent years; however one neglected area that can have a large effect on this is the energy usage for the interior climate. This study aims to investigate the energy usage for the interior climate for different conditions by measurements on a complete vehicle. Twelve different NEDC tests in different temperatures and thermal states of the vehicle were completed in a climatic wind tunnel. Furthermore one temperature sweep from 43° to −18°C was also performed. The measurements focused on the heat flow of the air, from its sources, to its sink, i.e. compartment. In addition the electrical and mechanical loads of the climate system were included. The different sources of heating and cooling were, for the tested powertrain, waste heat from the engine, a fuel operated heater, heat pickup of the air, evaporator cooling and cooling from recirculation.

The aim of this method is to measure emissions from components in the fuel system in a way that is comparable with regulated measurements by Sealed Housing for Evaporative Determination (SHED). In a circuit, constructed as a differential reactor, air is circulated between a test cell and a flame ionization detector (FID) for total hydrocarbon measurement. A test object, i.e. a fuel system component, is filled with fuel and placed in a sealed test cell. Due to the flow characteristic, equilibrium will occur between the air and the fuel evaporated from the surface of the test object. The amount of air consumed in the reactor is compensated by pure air being added to the system. The concentration of hydrocarbon in the circulated air is continuously measured by the FID.

The article describes a model-based control method for idle speed of spark-ignition (SI) engines. It is based on mid-ranging, a multivariable control strategy that is more commonly used in process control. The basic building blocks of the control structure are two PI controllers.

In May 1998 Volvo launched its most exclusive car model so far, the Volvo S80, which is aimed to compete with upper luxury segment products. The car is produced in the new production facility in the Torslanda plant in Sweden. Among the more highlighted features were a transversely mounted in-line six cylinder engine with a specially designed gearbox, electronic multiplex technology with 18 computers in the network, and safety features like stability and traction control (STC), front seats with integrated antiwhiplash system (WHIPS) and inflatable curtain (IC) for improved side impact protection. To fulfill the product's high demands on safety, quality and environmental care, the design, materials selection and assembly of the car body with high precision had to be very carefully engineered. As in previous product-/process development a holistic and concurrent engineering approach was necessary.